Announcement

Collapse

General Forum Rules

This forum is open to all brands and aftermarket products.


No flaming or insulting other members, everyone is entitled to their own opinion.


Treat others how you want to be treated. If you do not have anything nice or productive to say, then don't say anything at all. Remember, you are interacting with real people and if you wouldn't say it to their face, then you probably shouldn't type it. Don't be a keyboard warrior!


No profanity. Dropping f-bombs doesn't make you cool.


Absolutely no obscene or pornographic content is allowed

Please post in the appropriate sections

Do not email, PM, call, or carrier pigeon etc. ADA Racing or admin with complaints about bans or Billetboard drama. If you were banned, it was for a reason and we're too busy to deal with those kind of complaints. If you have an issue with a moderator, please PM said moderator or any of the other moderators and if they have time to address it they will. Remember, we offer this board as a service to the community and it is a privilege to be on here, not a right.

Any member violating the above rules will be banned

These rules may be updated at any time
See more
See less

need some simple help(ORC)

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • need some simple help(ORC)

    Hey everybody just wanted alittle info on my new ORC thats in the mail. ok i ordered an .800 spindle and a drive bolt with my ORC and how do i put on the spindle, do i just slide it on or cover it and hit it lightly, please don't flame. what should i do for the carb settings?? breaking it in?? thanks to anybody that helps me out. and please don't flame on me
    yellow sport with ada series 1, ada HP carb, ada superior carbon air filter, red scooterpros coolhead,

  • #2
    ok, well if its in the mail im assuming that its new, if so then the carb settings are set to be for break in, after that you wanna turn the high in in small incrememts untill you get the best throttle response, then richen it up a minute tad, and for the spindle, the shaft is tapered so all you have to do is set the spindle on the shaft and then tighten down the spindle bolt, the taper does the rest, but make sure its tight, and with an 800, get a pipe, it really makes you move i know
    2002 Sport with Diamond Plate deck, ADA billet Throttle and brake levers, 5" Monster Tach with shift light" yea, it works too" Billet gas cap, 900. Black Magik Spindle with ADA 3rd Bearing Support, Chrome Fancover, ADA Solid Bead Lock and ADA solid front Rim, Ported Big Bore and 1MM Stroked G230RC, with a Kool Head and an Engine Trix Pipe.

    Comment


    • #3
      Actually, Most motors don't come with the carbs pre-set. Anyhow the Carb settings should be as follows: High 1 1/4 out and Low 1 1/2 out. The idle screw (big screw below the fuel mixture needles) should be all the way in.
      Ada All the way.

      Comment


      • #4
        Eh, hem, ALL new motors have a factory pre-set.
        2002 Sport with Diamond Plate deck, ADA billet Throttle and brake levers, 5" Monster Tach with shift light" yea, it works too" Billet gas cap, 900. Black Magik Spindle with ADA 3rd Bearing Support, Chrome Fancover, ADA Solid Bead Lock and ADA solid front Rim, Ported Big Bore and 1MM Stroked G230RC, with a Kool Head and an Engine Trix Pipe.

        Comment


        • #5
          i have an S1 on my lh and so it supposed to have carb settings already set
          yellow sport with ada series 1, ada HP carb, ada superior carbon air filter, red scooterpros coolhead,

          Comment


          • #6
            Originally posted by Mailbox
            Eh, hem, ALL new motors have a factory pre-set.
            I don't think 2 turns out on the high and one on the low is a preset. All the Motors ive ever opened out of the box are never even close to the normal carb settings.
            Ada All the way.

            Comment


            • #7
              Why should High and Low speed jets be set with idle screw all the way in instead of al the way out?

              Thanks

              Comment


              • #8
                well, you didnt think outside the box, it was a trick reply really, any thing that comes out of the factory is a preset, weither it be all the way closed or 1 1/7834, turn out. i was just being a smart A5S. so no hard feelings, i just hate being questioned.
                2002 Sport with Diamond Plate deck, ADA billet Throttle and brake levers, 5" Monster Tach with shift light" yea, it works too" Billet gas cap, 900. Black Magik Spindle with ADA 3rd Bearing Support, Chrome Fancover, ADA Solid Bead Lock and ADA solid front Rim, Ported Big Bore and 1MM Stroked G230RC, with a Kool Head and an Engine Trix Pipe.

                Comment

                Working...
                X