Tweet
I have a TSI with stock carb setup, a K & N Filter w/ v-stack and choke, so I bolt the juicebox and plastic spacer to cylnder, everything is good, then I go to tighten carb , vstack, and choke to the juice box and it wont tighten down all the way but it will tigthen down fine with stock manifold this really sux now i have to buy shorter carb screws or something and also do i need to cut the engine shroud it seems like the juice box is a tight fit with it
-
-
Take a hack saw and cut a tiny bit off the screws.Ada All the way. -
i got shorter screws.... but do i need to cut the engine shroud?Comment
-
I didnt need to cut the motor cover at all. It fit fine.Comment
-
well it actually puts pressure on the engine cover so i cut it out in a perfect box where the juice box but pressure on the engine coverComment
-
Well i did a filter swap i took the TGN Filter and carb screws from my sxp and put that on my tsi and put my tsi carb screws and k and n filter on my sxp i can use the juice box, and i have to say the juice box didnt do anything its a complete waste it actually decreased performance.Comment
-
Well..Originally posted by gopedder13
Well i did a filter swap i took the TGN Filter and carb screws from my sxp and put that on my tsi and put my tsi carb screws and k and n filter on my sxp i can use the juice box, and i have to say the juice box didnt do anything its a complete waste it actually decreased performance.
#1 You have it tuned improperly
#2 You cannot tell a power difference
#3 You installed something wrong
Everyone that has gotten a juice box has loved it, and your the only one that has said something negative about it. What does that say?Ada All the way.Comment
-
1. No, its tuned perfect, its teh stock tsi carb it isnt that hard to tuneOriginally posted by Slimcandy428
Well..
#1 You have it tuned improperly
#2 You cannot tell a power difference
#3 You installed something wrong
Everyone that has gotten a juice box has loved it, and your the only one that has said something negative about it. What does that say?
2. Then what should i be able to tell?
3. I checked it over 4 times, everything is rightComment
-
I can only tell you what my ride did.
ADA Head and 17:1 dome, ADA HP Carb Kit, ADA GSR Pipe.
I rode my scooter before and just verified how it ran.
I installed it, and had to richen the needle valve a bit, and rode it again. The powerband came on earlier, and stay'd on later. Acceleration was noticeably smoother and stroger.
I'm leavin it on mine!Comment
-
And I had the same results as JBonnardel. My ADA Juice Box fit PERFECT and with minor carb tuning I had a noticeable improvement in throttle response. I have a tsi with TS head kit(15:1), JetproGSR pipe, and stock tsi carb.
Great product, excellent fit and finish, nice improvement in throttle response.Comment
-
Blown, i have an Identical set up to you. If you could please tell me what your needle is set at, i would really appreciate it. I just tryed some carb tuning and I do have to say I think i noticed some better throttle response and the powerband did seem to be a bit longer.Originally posted by blownC5
And I had the same results as JBonnardel. My ADA Juice Box fit PERFECT and with minor carb tuning I had a noticeable improvement in throttle response. I have a tsi with TS head kit(15:1), JetproGSR pipe, and stock tsi carb.
Great product, excellent fit and finish, nice improvement in throttle response.Comment
-
well i actually am starting to like it better and im starting to notice a performance gain. ive been working on tuning my carburator i think i have it pretty good, btu since i have such a similiar setup to blown i would appreciate it if he told me his carb setting...
<image src="http://stranglethecat.com/Uploads/4/mikestsiengine.jpg">Comment
Comment