-- Kman's Big-Foot (updated) --

[Kman]

On Friday night, I took apart my go-ped motor because I had an air leak. When I got my cylinder off, the cylinder gasket (the gasket that goes between the cylinder and cases) was ripped in two places. I replaced the cylinder gasket and put my motor back together. I rode my ped for five minutes, and the cylinder gasket blew again. I forgot to tighten down the two cylinder bolts tight (stupid me). I replaced the gasket again, and it running great!

Saturday, I went to a welding show all day with my dad. I did a little bit of MIG welding. After that, I got alittle bit bored, so I made a alminum stand for my Go-Ped. I measured and cut out all the pieces I needed to make my stand. I had one of the best TIG welders in American; Bruce Hollingshead, TIG weld my stand together.


Here are two pictures of my Go-Ped stand:




I bought my Go-Ped in May of 2003 from Jason at Coast Ped.

ADA Parts:
? ADA s2 Pipe
? ADA Front Suspension (mechanical)
? ADA Front Billet Wheel w/ Rotor
? ADA Rear Billet Wheel
? ADA Air Filter w/ Velocity Stack

Non ADA Parts:
? Big?Foot
? G260RC Motor
? Pro Flow Manifold
? The Works Pipe Mount
? Pipe Wrap (not on at the moment)
? Team FourSum Air Scoop (black)
? WT-603 Carb
? TGN Throttle Linkage
? Iridium Spark Plug
? PMW Lockout
? .710 Black Magic Spindle
? MLC Pole ? Meyer Handlebar (black)
? ODI Rogue Grips
? Kenda II Tires
? 1.5 Liter Gas Tank
? Billet Fuel Filter
? Douglas at Earth Surfer Products worked on my motor.


Here are a few updated pictures of my Go-Ped:













I plan on getting a Meyer Concave deck soon.

Please rate my ped. No flamming please!

Fixed your pictures,

Alan

[Slimcandy428]

Sweet!

BTW, Img tags are enabled now.

[CBlakeNS]

Nice man! I love that stand toooo!

[Kman]

Thanks Alan, I didn't know the img tags worked.


Thanks for the nice comments!

[stitch]

omg i love that bf, just get a billet deck, btw what pole is that mlc, rancho or pro pole?

[stitch]

ok, i stopped being ignerant and read, so its a pro pole, can you measure the length from the top to the bering cups, i wanna know so i can compare the length

[Sick Shift]

ok, i stopped being ignerant and read, so its a pro pole, can you measure the length from the top to the bering cups, i wanna know so i can compare the length

It's a MLC pole....

[Kman]

I believe my MLC pole is 25 1/4 inches tall.

[chip]

Bling stand!

I still have my PVC-made stand ... but it doesn't work with my Horn'd GSR40

(No space under my deck anymore)

[Sick Shift]

I believe my MLC pole is 25 1/4 inches tall.

BTW, cut that down like 3 inches, Mine were cut down almost 4, so much more comfortable.

[Kman]

Alan, good idea, but you need to remember I am 6'3".

[Bill L.]

i must say i love your bigfoot just get a meyer deck and have it powdercoated

[stitch]

k man you are 6 in taller than me how old are you?
btw, is there any slop or wobble in the pole?

[Kman]

k man you are 6 in taller than me how old are you?
btw, is there any slop or wobble in the pole?

I'm 15 years old. There is zero slop or wobble with the MLC pole. I love it.

[Kman]

I won the DDM contest for the month of March 2004, so I got a Meyer Concave deck. Should be here by Wed.